Products
AMC72-DV DC Volmeter Analyzer
GENERAL
Parameters
Accuracy
Current:Class 0.5
Power Supply
AC 220V
Current:Power consumption
< 0.5VA
Power supply
power consumption≤5VA
Installation
Embedded installing
Starting current
0.3%
Faceplate(L×W)
75*75mm
Cutout(L×W)
67*67mm
Housing(L×W×H)
66*66*98mm
Switch relay
DC 30V/3A AC 220V/3A
Technical Datasheet
| Technical Parameter | Value | |
Input |
Rated Value |
AC voltage:Single phaseAC 100V, 400V Three phaseAC 100V, 400V, 660V(UL-L, Only 72/ 96) AC current:AC1A, 5A; DC voltage:1000V, 300V, 75mV, 10V; DC current: 0-20mA, 4-20mA, 5A; |
| Overload |
Voltage: 1.2 times rated value(continuous); 2 times rated value /1 second Current:1.2 times rated value(continuous); 10 times rated value /1 second |
|
| Frequency | 45Hz～65Hz |
|
| Power Consumption | Power consumption of each voltage, current input circuit is less than 0.5VA |
|
| Accuracy | Class 0.5 | |
Function |
Display | LED or LCD |
| Communication |
RS485, Modbus-RTU protocol;(1 start bit, 8 data bit, 1 stop bit, no parity) Baud Rate 2400/4800/9600/19200 bps etc. |
|
| Alarm | 1 channel passive relay, contact capacity 3A/30VDC, 3A/250VAC, Used for high, low, unbalance alarm etc. |
|
| Analog |
DC4~20mA, ( load <500Ω) (note:Shielded wire is specially selected for the above signal input and output) |
|
| Switching |
Input:4 channel or 2 channel dry contact Input, built in power supply Output:2 channel switching output, NO relay contact, capacity:3A/30VDC, 3A/250VAC |
|
| Auxiliary Supply | AC/DC 85-265V |
|
| Power Consumption | <5VA |
|
Insulation resistance |
≥ 100MΩ |
|
Power frequency withstand voltage |
Between power supply set of terminals and signal input, output set of terminals 2kV/1min (RMS) Between the shell and all set of terminals(except the set of terminals reference voltage less than 40V) AC 4kV |
|
Environment |
Temperature | Operation: -10℃～+55℃Storage: -25°C ~+70°C |
| Humidity | ≤95%RH, no condensation, without corrosive gas |
|
| Altitude | ≤ 2500m |
|
Dimension
Wiring
Network
Installation
FAQ
Q: No display on power?
A: Check whether the supply voltage is within the operating voltage range.
Q: Incorrect reading of voltage,current, electricty, etc?
A: Checking that the voltage/current ratio setting are correct;
Checking whether the wiring mode setting is consistent with the actual situation;
Checking whether the voltage transformer and current transformer are in good condition.
Q: Abnormal communication
A: Check whether the adress,baud rate,check bits in the communication;
Setting are consistent with the host computer;
Check whether the RS485 converter is normal;
Check the connection is corrent if the resistor above 120 ohm is connected in parallel at the communication end.
PACKAGE
MINIMUM PACKAGE |
 |
 |
 |
 |
MINIMUM PACKAGE |
Package Dimension(1 PC) 230*145*120mm |
Pakage Weight(1 PC) 0.58Kg |
||
WHOLE BOX PACKAGE |
Package dimensions(36 PCS) 615*480*120mm |
Pakage Weight(36 PCS) 13.5kG |
||
PRODUCT HS CODE |
9028301300 |
|||
ATTENTION !
The above packing and weight data are only refer to model AMC72-DV.
For other models or optional functions, please contact the salesman for details, thank you for your cooperation!
